How To Fix Chainsaw Battery Charger Blinking Red? (Guide)
- Disconnect battery and charger, wait, then reconnect both.
- Ensure charging environment isn’t too cold.
- Check battery for defects or depletion, follow manufacturer’s manual or contact support.
- Inspect charger connections; contact support if issue persists.
- Clean battery and charger contacts from debris or corrosion.
- If problems persist, consider replacing battery or charger.
The chainsaw battery charger is constantly blinking red, even after charging for a long time!!!
A chainsaw Battery blinking red is one of the most frustrating things a woodcutter can experience.
This happens when the charger fails to maintain the charge of the battery.
The issues can be either in the battery or charger.
This post will look at the reasons why your battery is blinking red and how to fix the problem.
Why Chainsaw Battery Charger Blinking Red?
The temperature of the environment
Unless the environment’s temperature tends to be cold enough to charge the chainsaw, that charger may show the blinking red correct that indicates a low battery.
And the slow flashing should stop after such a short time or after the temperature falls to the appropriate range around 50 ° F and 86 ° F (10 ° C and 30 ° C). It suggests that perhaps the battery is low.
while charging becomes needed, briefly drain the batteries until you attempt anew.
Unless the light flashes red in around 90 seconds just after a storm’s initialization, its voltage level is also too low.
And it appears to be blinking red light, signalling that perhaps the chainsaw battery is put in charge.
Battery pack not used for a long time
Sometimes when we’re not using the battery for just a more extended period, it has been a problem and isn’t properly charged.
Both physical and chemical changes take place as the battery goes down, which can destroy that battery.
So keeping those charger batteries unused without any charging will usually eliminate this.
Bad connection of a battery to a charger
Suppose there is a weak connection between both the battery and the charger.
In that case, thus, the battery also isn’t appropriately charged and appears to indicate that perhaps the battery has low power and red light blinking upon this.
Issue With Battery pack
Chainsaw battery charger blinking red because the battery doesn’t charge properly.
It causes problems in both the battery and the charger.
Even trouble with the battery, and maybe you can use the incorrect Walt charger.
When you do not use the correct charger for the chainsaw battery, it causes that battery to be drained.
Should destroy the battery.
How To Fix The Blinking Red Battery Charger?
Fast flashing
Fast flashing suggests a weak link between the battery and the charger or a battery pack problem.
Please remove the battery from the charger using a clean fabric or cloth swap and wipe its metallic contacts on the battery.
Then try to charge the battery afterward.
Unless the flash continues, that battery may need to be repaired or replaced.
Dc Power Source
Use the Dc power source at the same voltage as the battery and connect the positive output to a positive battery terminal and the negative output to the negative battery terminal.
Once more, leave it connected for just a minute or two, instead begin charging the battery.
Battery Too Hot or Cold
The chainsaw battery charger is constantly blinking red, even after charging for a long time!!!
A chainsaw Battery blinking red is one of the most frustrating things a woodcutter can experience.
This happens when the charger fails to maintain the charge of the battery.
The issues can be either in the battery or charger.
This post will look at the reasons why your battery is blinking red and how to fix the problem.
If it was a warm day, and if you’ve now been utilizing the battery packs, but they’re incredibly hot, try throwing it throughout the fridge or taking it to a colder area for just a short period until going to charge it afterward.
Corroded or Dirty Battery terminals
The chainsaw battery charger could be given a faulty alternator or a loose battery terminal.
Before proceeding to replace the alternator, you should first check if the battery terminals are loose.
If you find that a terminal is loose, then you should tighten the terminal and make sure it is tightly locked into place.
Once this is done, you can check if the battery terminals are corroded or dirty.
You can clean corroded or dirty terminals.
Unless the steel connections mostly on the battery or charger are dirty or rusted, a chainsaw battery charger may incorrectly believe that the battery is damaged.
If the terminal becomes damaged, a piece of sandpaper can remove the rust.
The dust mostly on interfaces can be removed by either a cotton bud or perhaps an alcohol-soaked wipe.
It is difficult to find the actual ports because they are slightly raised; if that’s the situation, you will need to try different tools or items to even get to it for cleaning purposes.
Check with Another Electric Outlet
Check a voltage only at the electrical outlet with such a separate tool.
Make sure the outlet also isn’t turned out.
Unless the portable lamp is turned off when any breaker is turned off, leave the breaker off.
Go to a compact lamp or remove it from your first outlet. Insert that portable light into the second outlet.
Unless the portable light doesn’t switch on, both two outlets are all on the same loop.
Change Connector
Sometimes even the issue is a tiny metal connection in the connector, which may be slightly bent in just such a manner that this does not allow proper contact with the loading cord.
To fix it, firstly turned off the device and removed the battery.
Instead, put your battery back in, turn on your device, then try charging again.
Check Internal and External Damage or Issue
Check for defective contacts, power amplifier, or failure of an inverter.
The charger is subjected to trembling and, therefore, to irreversible internally and external damage.
It is adversely affecting leak, lengthy-term loss of capacity: connectors and Wires Dusty or damaged or split.
What If Neither Of These Solutions Was Going To Work?
If none of these remedies solves the chainsaw battery’s issues, you may have one of two issues: whether the battery is defective or the charger is inaccurate.
The best way to test the faulty component would be to take your battery down to your local shop that offers chainsaw battery tools and try it on one of their chargers.
If you have a similar fault, you get a faulty battery.
When there is no problem with yet another charger, it is probably a defective battery charger.
FAQ
How do I charge a battery?
What is a Ryobi Battery Problem?
How do I wake up a sleeping battery?
What is the difference between a lithium ion battery and an alkaline one?
What is the problem?
Frequently asked questions
Still have questions?
If you cannot find an answer to your question in our FAQ, you can always contact us
and we will be with you shortly.
Final Words
Battery chainsaws already achieved good results throughout the intellectual sense and have been capable of attaining higher slicing efficiency in some situations than the comparison model with the internal combustion engine.
The very first example was its chestnut wood test (Pellenc C20 and MSA160CBQ vs. MS 192 T) with a diameter of 80 mm for Pellenc and 100 for Stihl.
