What Is A Poulan Pro 3314 Chainsaw (Engine Specs)
The Poulan Pro 3314 is a small, homeowner-oriented gasoline chainsaw with a 33 cc, air-cooled, two-stroke engine. It is commonly paired with a 14-inch bar. Many 14-inch setups use a 3/8-inch low-profile chain, .050-inch gauge, and 52 drive links, but check your saw and bar before buying parts. Use the fuel mix specified for your exact manual.
If a manual or parts listing gives unfamiliar numbers, it can be hard to tell which ones matter. The key is to separate the saw’s engine specifications from the cutting parts fitted to a particular version. I start by checking the model label and the markings on the bar, rather than assuming every 3314 has the same replacement setup.
The figures below describe the 3314 configuration identified in available specifications. Parts can vary by version, so treat common fitment details as a starting point, not a substitute for checking the saw.
Poulan Pro 3314 engine and basic specifications
The 3314’s engine is a 33 cc, air-cooled, two-stroke gasoline engine. “CC” means cubic centimeters, a measure of engine displacement. The displacement helps identify the engine class, but it does not by itself tell you how quickly the saw will cut or what size wood it can safely handle.
| Specification | 3314 information | What it means |
|---|---|---|
| Engine type | Air-cooled, two-stroke | Runs on gasoline mixed with two-stroke oil, as specified by the manual |
| Displacement | 33 cc | Engine size, measured by cylinder displacement |
| Common bar length | 14 inches | The guide bar that carries and guides the chain |
| Common chain setup | 3/8-inch low-profile pitch, .050-inch gauge, 52 drive links | Chain dimensions for many 14-inch setups; verify before ordering |
| Fuel mix | 40:1 where specified in the 3314 manual | 3.2 US fluid ounces of two-stroke oil per 1 US gallon of gasoline |
The 14-inch bar is a common configuration, not a promise that every 3314 shipped with that exact bar or chain. Likewise, a 33 cc engine is not a reason to install a longer bar. Bar fit, oil delivery, chain type, and the saw’s instructions all matter.
The exact idle speed, maximum engine speed, chain-oil flow rate, fastener torque, and depth-gauge setting are not established here as verified 3314-specific figures. Use the applicable manual or the relevant component maker’s specification instead of guessing.
Fuel mix and chain oil
Two different lubricants matter on this saw: two-stroke oil mixed into the gasoline, and chain oil added to the separate bar-and-chain oil reservoir. The fuel mixture lubricates the engine’s internal parts. Chain oil reduces friction between the moving chain, bar, and sprocket.
Where the exact 3314 manual specifies a 40:1 fuel mix, that means 40 parts gasoline to one part two-stroke oil by volume. For one US gallon of gasoline, use 3.2 US fluid ounces of the correct two-stroke oil. Check the manual for your model and serial version before mixing; do not replace its ratio with a generic one.
Do not run the engine on straight gasoline. Too little two-stroke oil can leave engine parts without enough lubrication and may cause severe damage, including piston or cylinder seizure. Use fresh fuel mixed at the stated ratio, and keep it separate from the chain oil.
How to confirm bar and chain fit
Pitch, gauge, and drive links describe different parts of the chain fit. Pitch is the chain-size designation. Gauge is the thickness of the drive links that sit in the bar groove. Drive links are the small links that fit into that groove and travel around the bar.
| Check | Common 14-inch 3314 listing | How to verify |
|---|---|---|
| Bar length | 14 inches | Read the bar marking or the saw’s manual |
| Chain pitch | 3/8-inch low profile | Match the marking on the bar and the chain |
| Chain gauge | .050 inch, or 1.3 mm | Check the bar marking and chain packaging |
| Drive-link count | 52 | Count the chain’s drive links, or confirm the exact bar specification |
| Bar mount and oiling | Must match the saw | Compare the replacement bar with the original and the parts information |
These figures are commonly listed together for a 14-inch setup, but one matching measurement does not prove the chain fits. A chain with the right pitch but the wrong gauge or link count may not fit the bar correctly. The bar must also fit the saw’s mount and oiling arrangement.
Illustrative fitment check: If you are ordering a replacement chain, compare all three chain dimensions with the bar markings, then confirm the count. If you are replacing the bar, match its mount and oiling features to the saw as well as its length. This is a check procedure, not a claim about a particular owner’s repair.
Equipment setup and safety preparation
Setup means confirming that the saw, cutting parts, protective gear, and work area are ready before starting the engine. This check helps catch poor fit, damage, or unsafe conditions early. A correctly sized chain is not enough on its own; the chain brake, controls, handles, and work area also need attention.
Wear a helmet with face and eye protection, hearing protection, chainsaw-rated leg protection, gloves, and boots. Before starting, inspect the chain brake, throttle lockout, chain catcher, handles, bar, chain tension, and fuel and oil caps. Follow the manual and applicable worksite rules, including ANSI Z133 where it applies.
Clear the cutting area and plan an escape route before felling a tree. Keep bystanders at least two tree lengths away from tree-felling work. Felling, overhead cutting, and hazardous hung-up trees call for qualified personnel and an appropriate work plan.
Start the saw on stable ground with the chain brake engaged, following the manual’s starting steps. Do not drop-start it. After it starts, check that the chain stays still at idle and confirm chain lubrication using the manual’s method. If the chain moves at idle or lubrication is not confirmed, stop and consult the manual before cutting.
Field cutting and landscaping operation
The 3314’s engine and common 14-inch bar setup are intended for homeowner-scale cutting tasks, but the specification alone cannot establish that a specific cut is safe. The wood, saw condition, operator skill, and cutting method all affect the job. Keep the bar nose out of the cut and use a stable stance with both hands on the saw.
Rotational kickback is a sudden upward and backward movement that can happen when the upper tip of the bar contacts wood or another object. It can happen quickly. Keep the nose clear, maintain control, and use a properly maintained chain brake, but do not treat the brake as a substitute for careful cutting.
Do not cut above shoulder height, force a dull chain through wood, or operate with a loose or damaged chain. Do not assume that harder wood can be cut safely just because the bar is shorter or the engine has a particular displacement. For a task that needs a longer bar or specialized cutting method, check the manual and get qualified advice rather than modifying the saw based on engine size alone.
Maintenance, chain sharpening, and tuning
Maintenance keeps the saw’s cutting parts and engine in serviceable condition. For the 3314, follow the applicable manual for cleaning, adjustment, and service intervals. The exact chain-sharpening angles, depth-gauge clearance, engine speeds, and fastener torques should come from that manual or the chain maker’s instructions, not a universal estimate.
After use, inspect chain tension and condition. Clean the bar groove, oil ports, sprocket-cover area, and air-intake area as directed. A dull chain can encourage the operator to push harder, while a loose or damaged chain can create a hazard. Stop work if the chain is damaged or cannot be tensioned as the manual describes.
Do not tune the engine by guessed RPM or file the depth gauges, also called rakers, to an assumed universal clearance. Rakers affect how aggressively the chain cuts. Use the exact service information for the saw and chain, or have a qualified service provider handle adjustments you cannot verify.
Shutdown, storage, and seasonal care
Shutdown means stopping the engine safely, letting hot parts cool, and checking the saw before storage. These steps reduce the chance of accidental contact with a moving chain and make it easier to spot wear or damage before the next use. Follow the manual for fuel handling and storage.
Engage the chain brake, stop the engine, and allow the saw to cool before refueling or servicing it. Keep fuel away from heat, sparks, and flames, and follow the fuel container and manual instructions. Do not open hot fuel-system parts or service the saw while it is running.
Before storing the saw, clean the bar groove and oil ports, inspect the chain and tension, and cover the chain. Follow the manual’s directions for longer-term fuel storage and the saw’s storage position. If any safety control is damaged or does not work as intended, do not use the saw until it has been checked.
Frequently asked questions
How many cc is a Poulan Pro 3314?
It has a 33 cc engine.
What type of engine does the Poulan Pro 3314 have?
It uses an air-cooled, two-stroke gasoline engine.
What fuel mix does a Poulan Pro 3314 use?
Where the 3314 manual specifies 40:1, mix 3.2 US fluid ounces of two-stroke oil with one US gallon of gasoline. Confirm the ratio in the manual for your exact saw.
What size bar is common on the Poulan Pro 3314?
A 14-inch bar is commonly listed. Check your saw and its manual before buying a replacement.
What chain fits a 14-inch 3314 setup?
A commonly listed setup is 3/8-inch low-profile pitch, .050-inch gauge, and 52 drive links. Verify all three against the bar and chain markings.
Can I fit a longer bar because the engine is 33 cc?
Do not use engine displacement alone to choose a longer bar. Confirm approved bar fitment, mounting, and oiling details in the manual or parts information.
What are the 3314’s idle and maximum RPM?
No verified 3314-specific RPM figures are provided here. Use the correct manual or qualified service information rather than tuning by guesswork.
How do I check whether a replacement chain fits?
Match pitch, gauge, and drive-link count to the bar markings. For a replacement bar, also confirm the saw mount and oiling arrangement.
Does the chain brake prevent all kickback injuries?
No. The brake is a safety feature, not a replacement for controlled cutting, proper training, or keeping the bar tip clear of the cut.
What should I do if the chain moves while the saw idles?
Stop using the saw and consult the applicable manual or a qualified service provider. Do not continue cutting with a chain that moves at idle.
(This article was written by one of our staff writers, Evan Bradley. Visit our Meet the Team page.)
