Husqvarna 395 XP Weight (Powerhead & Bar Specs)
The Husqvarna 395 XP powerhead weighs 7.9 kg (17.4 lb), before adding the bar, chain, fuel, or chain oil. It has a 93.6 cm³ two-stroke engine rated at 4.9 kW. Bar fit depends on your saw’s version and mount; check its manual, bar stamp, chain pitch, gauge, and drive-link count before buying.
If you are comparing saws by weight, the key is to separate the powerhead figure from the weight you will handle while cutting. A fitted bar and chain add weight and change balance. Fuel and chain oil add more. Husqvarna’s listed 7.9 kg figure is useful for comparing bare saws, but it is not a ready-to-cut weight.
I also recommend treating bar length and chain details as a package, not as separate shopping choices. A bar must fit the saw, and its chain must match both the bar and the drive sprocket. Small spec differences can make parts incompatible, even when a listing says they fit a 395 XP.
Powerhead Weight, Bar Compatibility & Safety Setup
The powerhead is the saw body with its engine and controls, but without the cutting equipment or fluids. Husqvarna lists the 395 XP at 7.9 kg (17.4 lb) in this form. The guide bar, chain, fuel, and oil all raise operating weight, so confirm what a seller’s weight figure includes.
How to read the weight figure
The 7.9 kg (17.4 lb) powerhead figure is the most useful starting point when comparing the 395 XP with other saws. It does not tell you the weight of a complete, fueled saw. Nor does it show how the saw will feel with a short or long bar.
There is no reliable complete-saw weight to calculate from the powerhead figure alone. Bar and chain weights vary by length and design; fuel and oil levels also change the total. If ready-to-use weight matters to you, ask the seller what is included or weigh the assembled saw safely.
| What is included | How to use the figure |
|---|---|
| Powerhead only | Compare the saw body with other powerhead-only figures |
| Powerhead plus bar and chain | Ask for the bar length and chain type |
| Fueled saw with chain oil | Closest to working weight, but fuel and oil levels matter |
The engine displacement is 93.6 cm³, and rated output is 4.9 kW. Those numbers describe engine size and power, not the saw’s balance or total weight. Bar length, chain choice, and the work you intend to do still matter.
Bar length and chain fit
Bar length is the guide bar’s nominal cutting length, usually given in inches. The 395 XP is commonly associated with bars in the 18- to 36-inch range, but approved lengths can differ by market and saw version. Use the range in the manual for your exact saw rather than assuming every listed length is approved.
The chain must match three details: pitch, gauge, and drive-link count. Pitch is the spacing between chain drive links; gauge is the thickness of the drive links that sit in the bar groove. The 395 XP uses 3/8-inch pitch. Common setups use .058- or .063-inch gauge, but those gauges are not interchangeable.
Before ordering, check the bar stamp and the saw’s manual. Confirm the bar mount fits your exact model, then match the chain to the bar and drive sprocket. Verify the required drive-link count from the bar or chain maker’s specification. Do not rely on “fits 395 XP” alone if the listing does not give these details.
| Check | Required match | Why it matters |
|---|---|---|
| Bar mount | Exact saw version and mount | A bar that does not fit securely is not usable |
| Chain pitch | 3/8 inch, matched to sprocket and bar | Pitch mismatch prevents correct engagement |
| Chain gauge | Bar stamp, commonly .058 or .063 inch | Gauge mismatch can prevent proper seating |
| Drive-link count | Exact bar and chain specification | Incorrect length will not fit and tension correctly |
| Bar length | Manual-approved range for your market | Limits vary by configuration and intended use |
A longer bar can reach farther into a cut, but it also increases leverage and kickback exposure. It can make a saw feel heavier at the nose. Choose the shortest approved bar that suits the work, and do not select a long bar just because the engine can run it.
Choosing a setup for the job
These are fitment scenarios, not claims that every setup is approved for every 395 XP. Check your manual first. If your intended length is not listed for your saw, ask a Husqvarna dealer to confirm compatibility before buying the bar and chain.
| Intended work | Practical bar decision | What to verify |
|---|---|---|
| Smaller timber within the saw’s intended use | Consider a shorter approved bar | Mount, chain match, and whether the saw is suitable for the task |
| Mixed large-timber work | Choose an approved length that covers the usual cuts | Manual range, chain gauge, and drive-link count |
| Occasional cuts needing more reach | Use a longer bar only if approved | Added leverage, operator control, and increased kickback exposure |
The 395 XP is a large professional saw, but that does not make every large-bar setup a good choice. If you are upgrading from a smaller saw, compare complete operating weight and balance when possible, not just engine displacement or powerhead weight.
Setup and safety checks
Before use, wear a helmet with face and eye protection, hearing protection, chainsaw-protective legwear, gloves, and suitable boots. Inspect the chain brake, throttle lockout, chain catcher, handles, bar, chain tension, and lubrication system. Check the site for overhead hazards, lean, wind, nearby targets, and clear escape routes.
Start the saw on stable ground, with the chain brake engaged, and follow the manual’s cold- or warm-start procedure. At idle, the chain must not move. Check chain-oil delivery using the manual’s safe method; do not point the bar at yourself or another person.
Rotational kickback can occur if the upper quadrant of the bar nose contacts wood or another object. It can throw the saw toward the operator. Keep a firm two-handed grip, avoid nose contact, maintain a working chain brake, and do not cut above shoulder height. Large-tree felling and barber-chair risk call for trained personnel and a planned method, not an improvised cut.
Field Cutting and Landscaping Operation
A suitable setup is one that fits the saw, the wood, and the operator’s skill. Bar length alone does not decide whether a cut is appropriate. For this high-power saw, plan the work, use the correct chain, and keep control of the bar throughout each cut.
In a practical fitment check, I start with the wood and task, then work backward to the bar and chain. For example, a buyer planning mostly smaller-diameter cuts should not assume a long bar is an upgrade. A shorter approved bar may be easier to control, while a long bar adds reach but also increases leverage. The manual and operator capability set the limits.
Before cutting, check that the chain is sharp and correctly tensioned. A dull chain encourages excess force and can make control harder. Keep secure footing and a two-handed grip. Use felling methods and site controls consistent with ANSI Z133 and applicable OSHA requirements, and bring in trained help when the tree, lean, or hazards exceed your skill.
If you are evaluating a used saw, inspect the bar and chain as part of the purchase. A worn bar, damaged chain, or mismatched replacement parts can add cost and may point to poor maintenance. Confirm the bar mount, pitch, gauge, and drive-link count before pricing replacement parts.
Maintenance, Chain Sharpening & Tuning
Routine care protects the saw and helps the cutting system work as intended. Match chain sharpening and tension to the chain maker’s instructions, and follow the 395 XP manual for tuning and lubrication. Do not copy a generic setting from another saw or chain setup.
After cutting, switch off the saw and let it cool before cleaning or inspection. Check the air filter, bar groove, oil holes, chain, and sprocket area. Clear debris, look for damage, and retension only when safe and as directed by the manual. A chain can loosen as it heats, so recheck tension during work.
Use the fuel mix specified for your model and oil. With Husqvarna’s specified two-stroke oil, the stated ratio is 50:1, or 2%. If using another approved oil, follow the applicable manual. Never use straight gasoline or an incorrect mix; either can rapidly damage a two-stroke engine, including by causing seizure.
Set idle, high-speed mixture, and chain-oil delivery according to the manual and the fitted equipment. There is no single safe generic RPM, raker-clearance, or oil-flow setting for every chain, bar, and market version. If the chain moves at idle, the saw does not oil correctly, or the engine runs poorly, stop and diagnose the cause before cutting.
Storage and Seasonal Care
Good storage starts with a clean, inspected saw and the fuel directions in the manual. Remove sawdust and oil buildup from the cutting area, check the bar and chain for wear, and protect the chain from contact. Use the manual’s fuel and storage guidance rather than assuming one method fits every storage period.
Before putting the saw away, engage the chain brake, switch off, and let the engine cool. Clean the bar groove and oil holes, and inspect the chain and sprocket area. Store the saw in a dry, secure place away from children and ignition sources, with the bar cover fitted.
For a used or seasonal saw, note the exact bar and chain markings before replacing parts. This simple record helps prevent a later mismatch in pitch, gauge, or drive-link count. If the saw has been stored with fuel, follow the manual’s steps before starting it again.
Conclusion and FAQ
The key buying figure is 7.9 kg (17.4 lb) for the 395 XP powerhead, not the complete saw. Its 93.6 cm³ engine is rated at 4.9 kW, and its chain pitch is 3/8 inch. Before choosing a bar, confirm the approved length for your exact version and match mount, gauge, and drive-link count.
A longer bar may suit some large-timber work, but it adds leverage and kickback exposure. If you cannot verify the fit from the manual and bar markings, pause the purchase and confirm the setup with a qualified dealer.
How much does the Husqvarna 395 XP weigh?
The powerhead weighs 7.9 kg (17.4 lb), excluding bar, chain, and fluids.
Is 7.9 kg the ready-to-cut weight?
No. The figure excludes cutting equipment and fluids. A complete saw weighs more.
What engine size is the 395 XP?
It has a 93.6 cm³ two-stroke engine rated at 4.9 kW.
What chain pitch does it use?
The specified chain pitch is 3/8 inch. The chain must also match the sprocket and bar.
What chain gauge does a 395 XP use?
Common setups use .058- or .063-inch gauge. Check the bar stamp; these sizes are not interchangeable.
What bar lengths fit the 395 XP?
The saw is commonly associated with 18- to 36-inch bars, but approved lengths vary by market and version. Check the exact manual.
Can I use any 3/8-inch chain?
No. Gauge and drive-link count must also match the bar, and pitch must match the sprocket.
Does a longer bar make the saw heavier?
Yes. A longer bar and its chain add weight and can shift balance toward the nose. Exact added weight depends on the parts fitted.
What fuel mix should I use?
Use the applicable manual. With the manufacturer’s specified two-stroke oil, the stated mix is 50:1 (2%).
Can I adjust the carburetor or oil flow by a generic setting?
No. Follow the manual for the exact model and fitted equipment. Generic settings may not suit your chain, bar, or market version.
(This article was written by one of our staff writers, Marcus Thorne. Visit our Meet the Team page.)
