How Often to Clean Chainsaw Air Filter?

As a lumberjack, a DIYer, a student, or someone trained in the use of chainsaws, you’d agree that chainsaws are pretty important when it comes to activities like tree felling, pruning, cutting, and bucking, amongst others. It is, therefore, necessary to take good care of your chainsaws.

Chainsaws are similar to automobiles, in that, the more you use them, the more maintenance they need. However, experts suggest that you obtain a professional service or check-up every few months for heavy usage and once a year for fair use.

A chain sharpening here, a new spark plug there, and filter replacement is occasionally required. It has to be replaced when an air filter stops keeping dirt and debris from entering the chainsaw’s engine and exiting the carburettor. How do you go about doing all these? Keep reading. This article will guide you!

How Do I Know If My Air Filter Needs Cleaning?

Have you noticed that you’re consuming more gasoline than usual even though your working circumstances haven’t transformed? The primary cause is most likely a clogged or broken air filter. Another indicator that it’s time to give your filter some TLC is overheating and decreased productivity. Essentially, when the filter grows dirtier and clogged up, you’ll notice a change in how it sounds and behaves.

When Should A Chainsaw Spark Plug Be Replaced?

It is suggested just replacing the plug, which should be done at least once a year anyhow. Spark plugs are inexpensive! Before you attach the replacement plug, consult your user handbook to determine the required gap (the air space between the two electrodes at the end of the pin).

Can a chainsaw be pressure washed?

Its all up on what type of chainsaw you have. If you have a chainsaw, a good material, then it is one of the best and easiest way to clean your chainsaw. Always ensure deep cleaning of your chainsaw when its working is not good. Deep cleaning gives chainsaw a new look and gives it more strength to work properly. Infact, you can crap as a lube, so you can bring a proper lube for lubing. Naturally, your chainsaw will need to be well-oiled for it to function properly.

You may also clean the powerhead using compressed air, but we don’t advocate using a pressure washer since it can harm the air filter and electrical components if you’re not cautious. Rinse the filter with clean water after using the soap solution and dry thoroughly before reattaching it.

How Can I Use My Cleaner To Clean My Chainsaws?

Cleaning your chainsaw using a good cleaner product is a simple process. You might, however, feel confused or overwhelmed, and that’s why this article is here to offer a step-by-step guide on the best way to use any cleaner product to clean your chainsaw.

Step 1: Take some preliminary steps before cleaning.

Before you begin the actual cleaning of your saw, you should make sure that you’ve followed some preliminary procedures.

Ensure that your chainsaw is laid on a stable workbench securely, with its base flat against the table. Also, endeavor to keep your chain from every other thing on the work table.

Disconnect the battery (if it is battery-powered) or the cable ( if it is electric). You should drain the fuel if it is powered by gas.

Step 2: Disconnect the chain

It would help to use a wrench to loosen the nuts on both sides of the chainsaw’s bar. The wrench would assist in separating both the chain and the bar from the powerhead.

Step 3: Clean the chainsaw’s bar

It would be best if you cleaned the chainsaw bar using the a cleaner that contains degreaser. Mix the product in warm water and soak the bar with your solution. You can then use a rag or cleaning cloth to remove the dirt on the bar. A wire brush would also be handy in cleaning off difficult filth. It would help if you also cleaned the oil holes using an air compressor.

Step 4: Clean the saw’s chain

Using a specialist fast-acting degreaser and warm water mixture, soak the chain links for a minimum of 10 and a maximum of 15 minutes. Ensure to wipe out all forms of grime using your rag and wire brush. You can then rinse the chain with clean water and dry it with a clean rag. Please remember to air dry your chain.

How many times can a chainsaw chain be sharpened?

May typically polish a chain  3 to 5 times depending on use. A chainsaw’s air filter is essential. The device needs fresh air to work. When starting the chainsaw, sawdust, debris, and dust may enter. After ten hours, clean the chainsaw air filter. It depends on your working circumstances and the wood you’re cutting. You should clean your filter twice a year as a homeowner.

What Happens If You Don’t Clean Or Replace Your Air Filter?

Your chainsaw will continue to deteriorate. The less air your chainsaw air filter can suck into the engine, the dirtier and more clogged it becomes. The engine may begin to cut out and finally fail to start as a result of this. A clogged air filter in a rechargeable chainsaw may cause overheating and poor performance. Finally, the longer you overlook a broken or obstructed filter, the more likely you will have additional problems, such as engine damage and reduced service life.


Being a handyman requires a lot of commitment. One of such is taking good care of your working tools. Your chainsaw must be given ample attention. From this article, it is concluded that for most people, the best time to clean or replace the air filter on a chainsaw is at the beginning of the cutting season.  Again, how often you use it and your conditions will determine how long it lasts. On the cautious side, most individuals will find that changing the air filter once a year is advantageous.

Leave a Comment

5 × 2 =